!DOCTYPE html> Lectrosonics DCHT E01 - Noyz Boyz Audio

Lectrosonics DCHT E01

Digital Camera Hop Transmitter, accepts 2 channels mic level, line level or AES signals, 2x AA powered or external DC powered by optional LTBATELIM , 470.100-614.375 MHz , 10/25/50mW

Lees meer...
Artikelnummer: LECD-SDCHT7518

The new DCHT/E01 transmitter is designed for use in film and television production to provide a wireless link from a bag or cart system to cameras and recorders. The transmitter will accept mic or line level analog signals or AES digital signals from a mixer and transmit the signals to the receiver in a pure digital format. The digital architecture is a third generation design with specially developed, high efficiency digital circuitry for extended operating time on two AA batteries.

The transmitter can tune in coarse or fine steps across the UHF television band from 470.100 to 607.950 MHz, with a selectable output power of 10, 25 or 50 mW. The pure digital architecture enables AES 256-CTR encryption for high level security applications.

Studio quality, stereo audio performance is assured by high quality components in the preamp, wide range input gain adjustment and DSP-controlled limiting. Input connections and settings are included for any lavaliere microphone, dynamic microphones and line level inputs. Input gain is adjustable over a 51 dB range in 1 dB steps to allow an exact match to the input signal level, maximizing the dynamic range and signal to noise ratio.

The top panel contains the antenna jack, two audio input level LEDs (one per audio channel), the programmable function switch and the audio input jack. The red/green LEDs provide audio level indications from -20 dB to the onset of limiting for each channel for accurate input gain adjustment. The programmable switch can be configured as a mute switch, a power on/off switch, or be bypassed. The 6-pin input jack accepts two mic or line level analog signals or AES digital signals from external sources via a variety of adapter cables. Analog inputs can be linked for the same gain when used with a stereo source, or operate independently with individual settings.

The housing is constructed of solid machined aluminum for lasting ruggedness. The exterior is finished with an ultra hard, dark electroless nickel finish.


Operating Frequencies:470.100 - 614.375 MHz
Frequency Selection Steps:25 kHz
RF Power Output:Selectable; 10, 25 or 50mW
Frequency Stability:± 0.002%
Spurious Radiation:Compliant ETSI EN 300 422-1 v2.1.2
Digital Modulation:8PSK
Equivalent Input Noise:-128dBV
Input LevelMic: Nominal 2 mV to 300 mV, before limiting Greater than 1V maximum, with limiting
Line: +24dBu before limiting
Input Impedance:Mic: 300 or 4.5 kΩ; selectable
Line: greater than 100 kΩ
Input Limiter:Dual envelope type; 30dB range
Gain Control Range:51 dB in 1dB steps; digital control
Modulation Indicators:Bicolor LED indicates modulation of -20 and 0dB referenced to full modulation
LCD bar graph
Compatibility Modes:DCH (Digital Camera Hop)
Duet (IEM)
Frequency Response:20 Hz -14.5 kHz ±1dB
Controls:Top panel toggle switch; programmable as power, mute or none (off) function
Side panel membrane switches with LCD interface for power on/off and all setup and configuration controls
Audio Input Jack:Switchcraft 6-pin locking (TA6F)
Antenna:Galvanized steel, flexible wire, SMA connector
Battery:Two AA Duracell Quantum recommended
Battery Life:5 hours; Duracell Quantum alkaline
Weight:163 grams; w/ belt clip and lithium AA batteries
181 grams; w/ belt clip and Duracell Quantum AA batteries
Overall dimensions:88 x 62 x 19 mm
Emission Designator:200KG1E
0 sterren op basis van 0 beoordelingen
Wij slaan cookies op om onze website te verbeteren. Is dat akkoord? Ja Nee Meer over cookies »